K1
Senior Member
- Joined
- Aug 26, 2012
- Messages
- 455
- Reaction score
- 24
- Points
- 0
Test Cyp Conversion (Pics)
- Thread starter K1
- Start date
K1
Senior Member
- Joined
- Aug 26, 2012
- Messages
- 455
- Reaction score
- 24
- Points
- 0
Step #3
A. Heat a pan or pot of water just to the point where it starts to boil then pull it off and onto a burner heat is off.
B. Then place the vial into the water and let it sit for about 10-15 minutes. Give it a swirl and or stir with the glass rod to help it melt in the solution.
A. Heat a pan or pot of water just to the point where it starts to boil then pull it off and onto a burner heat is off.
B. Then place the vial into the water and let it sit for about 10-15 minutes. Give it a swirl and or stir with the glass rod to help it melt in the solution.
Attachments
K1
Senior Member
- Joined
- Aug 26, 2012
- Messages
- 455
- Reaction score
- 24
- Points
- 0
K1
Senior Member
- Joined
- Aug 26, 2012
- Messages
- 455
- Reaction score
- 24
- Points
- 0
Step #6
At this point you can placea stopper on the vial and shake it well. Then place it in the bath of hot water for approx 15 minutes.
***Note: it may take some time for it to fully suspend and may look grainy but it will suspend... it just takes a little time.
At this point you can placea stopper on the vial and shake it well. Then place it in the bath of hot water for approx 15 minutes.
***Note: it may take some time for it to fully suspend and may look grainy but it will suspend... it just takes a little time.
Attachments
K1
Senior Member
- Joined
- Aug 26, 2012
- Messages
- 455
- Reaction score
- 24
- Points
- 0
Step #8
This set-up will look familiar to those who have make Fina.
The set-up is a sterile vial that is vented and the whatmen filter attached to an 18 guage pin.
You will draw from the vial and then cover the pin and detach it from the syringe. Then re-attach the syringe to the whatman filter that stays attached to the vial.
Slow and steady you will push the product through the filter using the 10ml. syringe.
You will do this till all the product is filtered AND keeping track of how many mls you push through.
You will want to even it out in the end and purge the filter with whatever amount of sterile oil is nessesary to make it 50mls. This will also get all the remaining product flushed out of the filter.
You final product will be a painless 200mg/ml @ 50mls of Test Cyp.
This set-up will look familiar to those who have make Fina.
The set-up is a sterile vial that is vented and the whatmen filter attached to an 18 guage pin.
You will draw from the vial and then cover the pin and detach it from the syringe. Then re-attach the syringe to the whatman filter that stays attached to the vial.
Slow and steady you will push the product through the filter using the 10ml. syringe.
You will do this till all the product is filtered AND keeping track of how many mls you push through.
You will want to even it out in the end and purge the filter with whatever amount of sterile oil is nessesary to make it 50mls. This will also get all the remaining product flushed out of the filter.
You final product will be a painless 200mg/ml @ 50mls of Test Cyp.
Attachments
Similar threads
New Threads
-
-
TUESDAY TREAT 30% OFF ON EVERYTHING YOU LOVE- Started by YOURMUSCLESHOP
- Replies: 0
-
Go BIG , SAVE BIG
- Started by YOURMUSCLESHOP
- Replies: 0
-
Anabolic Steroids advice for beginners- Started by Protax
- Replies: 17
-
Canada domestic peptides Supplier
- Started by Sophia
- Replies: 0
