Results 1 to 9 of 9
  1. #1
    Senior Member K1's Avatar
    Join Date
    Aug 2012
    Posts
    455
    Thanks
    0
    Thanked 12 Times in 9 Posts

    Conversion Guide

    By: Anon

    1. Assemble all ingredients & utensils you will need:

    (from left to right, top to bottom) electric frying pan, glass stir rod, .22 micron syringe filters, benzyl alcohol (BA), benzyl benzoate(BB), 200ml glass beaker, electric scale (50g), various sealed sterile vials, ethyl oleate (EO), various syringes, various needles. (not pictured is grape seed oil (GSO))
    Attached Images Attached Images

  2. #2
    Senior Member K1's Avatar
    Join Date
    Aug 2012
    Posts
    455
    Thanks
    0
    Thanked 12 Times in 9 Posts
    2. Sterilize & clean your workspace & utensils, BA works well. (This is important but not as much as everyone thinks, you can use unsterile oil, unsterile powder & unsterile utensils, cause it will all be filtered & baked in the end)

    2.2. You enter all your ratios & amounts in the top section & as you can see the calculator will tell you exactly how much oil, powder, BA & BB you will need in the results box.
    CALCULATOR LINK - Powder Calculator

    3. Work out what concentration & ratios you are going to make your batch.
    3.1. We are going to call the powder ĎPí, this batch will be 50mlís @ 75mg/ml, with 3% BA & 20% BB (powder weight stays at .75)
    Attached Images Attached Images

  3. #3
    Senior Member K1's Avatar
    Join Date
    Aug 2012
    Posts
    455
    Thanks
    0
    Thanked 12 Times in 9 Posts
    4. Put an inch of water in an electric fry pan, you want to heat the water so it just below boiling point (about 70-80 degrees celcius/212 degrees Fahrenheit)

    5. Weight out your powder. Notice the calculator called for 3.75 grams of powder, Iím using 3.83 grams cause Iíd rather the gear slightly overdosed. (yes that is a piece of paper I am weighing the powder on, refer to point #2)
    Attached Images Attached Images

  4. #4
    Senior Member K1's Avatar
    Join Date
    Aug 2012
    Posts
    455
    Thanks
    0
    Thanked 12 Times in 9 Posts
    6. Place the powder in your beaker. Now draw up your BA (in this case itís 1.5 mlís) & spray it on the powder. Now draw up you BB (in this case itís 10mlís) & spray it on the powder.
    Attached Images Attached Images

  5. #5
    Senior Member K1's Avatar
    Join Date
    Aug 2012
    Posts
    455
    Thanks
    0
    Thanked 12 Times in 9 Posts
    7. Place the beaker in the warm water & stir gently until all the powder is dissolved (can take a few minuets depending on the powder)
    Attached Images Attached Images

  6. #6
    Senior Member K1's Avatar
    Join Date
    Aug 2012
    Posts
    455
    Thanks
    0
    Thanked 12 Times in 9 Posts
    8. Now draw up your oil, the calculator called for 35.69mlís, we will round that down to 35 so it gives use more chance of our batch being slightly over dosed.
    8.1. I am going to substitute some of the oil for EO & I recommend you do the same cause itís makes for a nice thin batch. In this case I will use: 25mlís GSO + 10mlís EO = 35mlís
    8.2. Draw 3mlís of the oil mix into a separate syringe and set it aside (I will explain later)
    8.3. Now take the remaining 32mlís and slowly add it to the powder in the beaker stirring occasionally until the solution is clear.
    Attached Images Attached Images

  7. #7
    Senior Member K1's Avatar
    Join Date
    Aug 2012
    Posts
    455
    Thanks
    0
    Thanked 12 Times in 9 Posts
    9. Use a large syringe (60cc is perfect) & attach an 18g needle to it & draw the solution up.

    10. Get a sterile vial large enough for the whole batch & place a 25g needle through the stopper (this will be used as a vent)
    10.1. Place an 18g needle onto a .22 micron syringe filter, then attach the filter to your syringe that contains the solution.
    10.2. Push the needle thorough the top of the vial with the vent pin in it and firmly push down on the plunger filtering the entire batch. ***I like to attach a caulking gun from the hardware to the syringe to make the job easier***
    Attached Images Attached Images

  8. #8
    Senior Member K1's Avatar
    Join Date
    Aug 2012
    Posts
    455
    Thanks
    0
    Thanked 12 Times in 9 Posts
    10.3. Now take the 3mlís of oil mix and attach it to the filter, press down on the plunger adding the oil mix to the batch. This will flush any remaining hormone that might be left in the filter out.

    11. Transfer the batch into some smaller 20 or 30ml vials with a 20cc syringe & a 21g needle
    11.1. Allow the vials to sit for 2-3 days so the BA can work on sterilizing the batch.

    12. Place 25g needles through the top of each vial as a vent, MAKE SURE THE needle IS NOT IN THE SOLUTION OR YOUR GEAR WILL LEAK OUT THE needle. Place the vials in an oven heated to 200 degrees Fahrenheit (93 degrees Celsius) for 30 minuets
    Attached Images Attached Images

  9. #9
    Senior Member K1's Avatar
    Join Date
    Aug 2012
    Posts
    455
    Thanks
    0
    Thanked 12 Times in 9 Posts
    You now have your very own home made batch of "P".... 50ml @ 75mg/ml. Enjoy!!!
    Attached Images Attached Images

Similar Threads

  1. Guide to Solvents, Compounds, Concentration, and Injection Pain
    By Goldy in forum Chemical Conversion and Homebrewing
    Replies: 6
    Last Post: 04-06-2012, 01:38 PM
  2. Guide To Cutting Fat 101
    By Stacked in forum Fat Burning and Weight Loss
    Replies: 0
    Last Post: 10-03-2011, 04:35 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •