Results 1 to 11 of 11
  1. #1
    Senior Member K1's Avatar
    Join Date
    Aug 2012
    Posts
    455
    Thanks
    0
    Thanked 13 Times in 10 Posts

    Test Enan Conversion w/ Pics

    By: 956Vette

    This will make test enan at 250mg/ml

    Things needed:
    A few syringes min 3ml ea(5-10ml preferred)
    A few needles 18-23g
    Alcohol wipes or another way to help ensure sterility
    2 sterile 10ml vials (must be identical)
    1ml benzyl alcohol (BA)
    1 .22-.44 pore size sterile syringe filter
    2.5 grams testosterone enanthate powder (typically a paste at room temp)
    11ml sterile oil
    pen/marker that will write on glass
    accurate scale
    some water or preferably rubbing alcohol
    Attached Images Attached Images

  2. #2
    Senior Member K1's Avatar
    Join Date
    Aug 2012
    Posts
    455
    Thanks
    0
    Thanked 13 Times in 10 Posts
    1-remove rubber stopper from 1 sterile vial by cutting the aluminum cap, use good scissors, nail clippers, metal shears, wire cutters etc…. once the metal cap is removed the rubber stopper will come off easily.
    Attached Images Attached Images

  3. #3
    Senior Member K1's Avatar
    Join Date
    Aug 2012
    Posts
    455
    Thanks
    0
    Thanked 13 Times in 10 Posts
    2-fill the vial you modified with exactly 6ml of water or rubbing alcohol. Precisely mark the top level of the water/rubbing alcohol using the pen/marker, by writing on the glass vial.
    Attached Images Attached Images

  4. #4
    Senior Member K1's Avatar
    Join Date
    Aug 2012
    Posts
    455
    Thanks
    0
    Thanked 13 Times in 10 Posts
    3-now add another 4ml of water to reach a total of 10ml.
    Attached Images Attached Images

  5. #5
    Senior Member K1's Avatar
    Join Date
    Aug 2012
    Posts
    455
    Thanks
    0
    Thanked 13 Times in 10 Posts
    4-again mark the level.
    Attached Images Attached Images

  6. #6
    Senior Member K1's Avatar
    Join Date
    Aug 2012
    Posts
    455
    Thanks
    0
    Thanked 13 Times in 10 Posts
    5-remove the water or rubbing alcohol from the vial and make sure it is COMPLETELY dry, try your best to not get any junk in the vial, let the water/rubbing alcohol evaporate, you may speed the drying process by placing it into a warm oven.

    6-use the scale to measure exactly 2.5 grams of enanthate powder.
    Attached Images Attached Images

  7. #7
    Senior Member K1's Avatar
    Join Date
    Aug 2012
    Posts
    455
    Thanks
    0
    Thanked 13 Times in 10 Posts
    7-add the enanthate powder to the modified vial.
    Attached Images Attached Images

  8. #8
    Senior Member K1's Avatar
    Join Date
    Aug 2012
    Posts
    455
    Thanks
    0
    Thanked 13 Times in 10 Posts
    8-using a clean needle and syringe: add .5ml BA to the enanthate powder and allow to dissolve completely.

    9-Usually some low supplemental heat is required to dissolve it completely.
    Attached Images Attached Images

  9. #9
    Senior Member K1's Avatar
    Join Date
    Aug 2012
    Posts
    455
    Thanks
    0
    Thanked 13 Times in 10 Posts
    10-add oil until you reach the level you previously marked off as the 6ml mark with the pen/marker.
    Attached Images Attached Images

  10. #10
    Senior Member K1's Avatar
    Join Date
    Aug 2012
    Posts
    455
    Thanks
    0
    Thanked 13 Times in 10 Posts
    11-stir, or shake, or use low heat to ensure things mix properly.

    12-using a fresh syringe and needle: while the oil enanthate mix is still warm, sterile filter it into the non modified(sealed) sterile vial. Use an alcohol wipe on the rubber stopper prior to penetrating it with the fresh needle. also place an extra needle through the rubber stopper to releive air presure.

    13-place the modified and the non modified vials directly side by side.
    Attached Images Attached Images

  11. #11
    Senior Member K1's Avatar
    Join Date
    Aug 2012
    Posts
    455
    Thanks
    0
    Thanked 13 Times in 10 Posts
    14-add more sterile oil through the sterile filter, into the sterile vial, until the oil level in the non-modified vial matches the 10ml mark you have made on the modified vial earlier. (this will be about 4ml usually) The purpose of this is to ensure complete purging of the enanthate /oil mix from the sterile filter, so a minimum amount is wasted.
    Attached Images Attached Images

Similar Threads

  1. Test 500mg/ml Conversion (Pics)
    By K1 in forum Chemical Conversion and Homebrewing
    Replies: 9
    Last Post: 04-14-2013, 04:54 PM
  2. Test Enan Conversion (Pics)
    By K1 in forum Chemical Conversion and Homebrewing
    Replies: 9
    Last Post: 08-28-2012, 08:46 PM
  3. Test Prop Conversion (Pics)
    By K1 in forum Chemical Conversion and Homebrewing
    Replies: 10
    Last Post: 08-28-2012, 07:21 PM
  4. Test Cyp Conversion (Pics)
    By K1 in forum Chemical Conversion and Homebrewing
    Replies: 8
    Last Post: 08-28-2012, 05:26 PM
  5. Test Enan Conversion (Pics)
    By K1 in forum Chemical Conversion and Homebrewing
    Replies: 0
    Last Post: 08-28-2012, 04:56 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •