2 oils in 1 syringe (could use some tips on this)

Mean Machine

SI Founding Member
Joined
Oct 5, 2012
Messages
17
Reaction score
1
Points
0
I am about to start my fourth cycle today and its my 1st time that i need to inject 2 different oils.

Usually I draw from vial with a 20 guage and inject with a 25 guage.


Will I need 2 different needles for the 2 oils?


please give me some tips.
 

chicken wing

Senior Member
SI Founding Member
Joined
Apr 27, 2012
Messages
462
Reaction score
30
Points
0
I use the same needle to draw from multiple vials and I pin with a new one.
 

j2048b

Elite
SI Founding Member
Joined
Jul 2, 2012
Messages
5,301
Reaction score
2,405
Points
238
I use to use 1 neeedle per vial, and the second needle used for the second vile, pin w it! No worries, no sense in waisting 3 needles, or even draw both as described and back fill a ton of syringes and ur set for a few injections
 

dboldouggie

Senior Member
SI Founding Member
Joined
Jul 17, 2012
Messages
149
Reaction score
4
Points
0
I use the same needle to draw all my gear then I use a different just to inject.
 

cotton2012

Elite
SI Founding Member
Joined
May 17, 2013
Messages
471
Reaction score
100
Points
0
You can use two oils in same syringe. Draw first oil like you normally would, then draw enough air into the syringe between the 1st oil and needle to take the place in the second vial for the second oil. After you jab it in keep the air above the 1st oil and push air into the second vial, I usually allow a little air bubble to be left in the syringe as not to get any of the 1st oil into the vial of the second oil. At that point draw in the second oil to the point you want, (I go a little past here) and then push out excess air. Keep a steady hand to not mix the oils causing you to get any of the first oil into the second vial as you push the excess back into the second vial. It easy once you get the hang of it. I wouldn't go more than 2ML in any large muscle group (glutes, quads) and stick to around 1ML in the smaller ones.


Cheers Cotton,
 

bubbagump

Elite
SI Founding Member
Joined
Oct 3, 2012
Messages
1,351
Reaction score
275
Points
63
I use the same needle to draw and pin. I change it once a week or so.


Just kidding. Don't do that....
 

Times Roman

Senior Member
Joined
Oct 27, 2012
Messages
1,020
Reaction score
24
Points
0
I use the same needle to draw from multiple vials and I pin with a new one.

^this

I'll mix anything oil based, or anything water based, (but not oil and water at the same time) all in the same syringe.

No need in using a bunch of tips.

one tip for drawing (if oil), and one tip for injecting.

Pretty simple really
 

Mean Machine

SI Founding Member
Joined
Oct 5, 2012
Messages
17
Reaction score
1
Points
0
thanks guys. pinned a couple of hours ago, and it went pretty good.
 

69nites

Elite
SI Founding Member
Joined
Jun 14, 2012
Messages
2,048
Reaction score
1,911
Points
113
I use to use 1 neeedle per vial, and the second needle used for the second vile, pin w it! No worries, no sense in waisting 3 needles, or even draw both as described and back fill a ton of syringes and ur set for a few injections
Do NOT prefil syringes with anything that is made with eo or g.

I'm telling you this from experience wasting hundreds of dollars in gear.
 

j2048b

Elite
SI Founding Member
Joined
Jul 2, 2012
Messages
5,301
Reaction score
2,405
Points
238
Do NOT prefil syringes with anything that is made with eo or g.

I'm telling you this from experience wasting hundreds of dollars in gear.

Noted 69 and thanks!
 

FreeBirdSam

Elite
SI Founding Member
Joined
Nov 23, 2012
Messages
782
Reaction score
214
Points
0
Do NOT prefil syringes with anything that is made with eo or g.

I'm telling you this from experience wasting hundreds of dollars in gear.


Good info here, I'll add that the reason for not doing this is because it degrades the rubber on the syringe's plunger, (imagine black swirls of melted rubber in your gear).. it will also leak most of it out.
 

Four1Thr33

Senior Member
SI Founding Member
Joined
May 1, 2012
Messages
2,117
Reaction score
63
Points
0
I also do the same ... But 3 oils and change the pin before injection
 
Joined
Aug 15, 2013
Messages
21
Reaction score
0
Points
0
I never put two in the same before. never even crossed my mind.
i try not to do more then 4 pins a weeks
 

NbleSavage

Veteran
SI Founding Member
Joined
Apr 29, 2012
Messages
11,984
Reaction score
11,954
Points
383
Pull from 2 or 3 depending, and pin with the same. Never had any issues. Always hit each vial with your alcohol pad before pulling from it and obviously alcohol pad on your injection site before pinning.

Be safe.

- Savage
 

transcend2007

Elite
SI Founding Member
Joined
Aug 20, 2012
Messages
4,190
Reaction score
3,396
Points
193
I draw from 3 vials with one pin, change to injection needle good to go.

I do use 2 different alcohol swabs. One for 3 vials of gear and a different one on the injection site.
 

New Threads

Top